- Centrifuge 5804/5804 R/5810/5810 R — Operating manual 1 Operating instructions 1 Operating instructions 1.1 Using this manual Please read this operating manual completely before using the device for the first time. Also observe the instructions for use enclosed with the accessories.
- The Centrifuge 5424 R is designed for separating liquid substance mixtures with different densities, in particular, for processing and analyzing samples from the human body in in-vitro diagnostic applications to ensure that the in-vitro diagnostic device can be used according to its intended purpose.
Advertising
Centrifuge 5424/5424 R
Operating manual
Centrifuge 5425 is the new laboratory standard. With its 24–place capacity and speed up to 21,300 × g, it is perfectly equipped for all modern molecular biology applications in Eppendorf and PCR tubes.
5404 900.023-02/0810
Advertising
This manual is related to the following products:
Table of contents- Operating manual
- User instructions
- 1.2 Warning signs and hazard icons
- Product description
- 2.2 Delivery package
- 2.4 Rotors
- Safety
- 3.3 Application limits
- 3.5 Warnings for intended use
- Installation
- Operation
- 5.4 Preparing for centrifugation
- 5.5 Cooling (only 5424 R)
- 5.6 Centrifuging
- Maintenance
- 6.2 Perform cleaning / disinfection
- Troubleshooting
- Transport, storage and disposal
- Technical data
- 9.4 Application parameters
- Ordering information
- 10.3 Accessories
- User instructions
- Declarations and Certificates
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
- en
Popular Brands
Popular manuals
Advertising
31
7 Troubleshooting
Centrifuge 5424 / 5424 R — Operating manual
7.2
Error messages
If one of the following error messages appears, proceed as follows:
1. Remove fault (see Remedies).
2. If necessary, repeat centrifugation.
1. Remove fault (see Remedies).
2. If necessary, repeat centrifugation.
Symptom / message
![Service Service](/uploads/1/2/5/0/125028597/651049748.jpg)
Cause
Remedy
LID ERROR
Centrifuge lid cannot be locked.
Try to close the centrifuge lid again.
LID ERROR
Centrifuge lid cannot be released.
1. Switch the device off and back on.
2. Press the open key.
If the error occurs again:
2. Press the open key.
If the error occurs again:
1. Switch off the centrifuge.
2. Activate the emergency lid release
2. Activate the emergency lid release
(see Emergency release on p. 32).
LID ERROR
Centrifuge lid must not be released during a
run.
run.
Wait for the rotor to stop.
LID LIFT
(only 5424 R)
(only 5424 R)
Centrifuge lid has not been opened wide
enough.
enough.
Open the centrifuge lid wider by hand.
INT
Mains power failure during a run.
Check the mains connection.
NO RPM
Error in speed measuring system.
Leave the device switched on until the
error message disappears (10 s or 6 min).
error message disappears (10 s or 6 min).
Err 6
Drive error. Cisco security plus license 5506.
Repeat the run.
If this error message appears again,
switch centrifuge off and back on again
after > 20 s.
switch centrifuge off and back on again
after > 20 s.
Err 6
Drive overheated.
Allow the drive to cool down for at least 15
min.
min.
Err 7
Major deviation in the speed control.
1. Wait for the rotor to stop.
2. Tighten the rotor.
2. Tighten the rotor.
Err 8
Drive error.
1. Wait for the rotor to stop.
2. Repeat the run.
2. Repeat the run.
Err 9 to 17
Electronics error.
Switch the centrifuge off and back on
again after > 20 s.
again after > 20 s.
Err 18
(only 5424 R)
(only 5424 R)
Too high temperature variation from nominal
value in the rotor chamber.
value in the rotor chamber.
Check the settings.
Check unhindered air circulation through
the vents.
the vents.
Thaw ice or switch off device and allow it
to cool down.
to cool down.
Err 19
(only 5424 R)
(only 5424 R)
Blackberry torch 9800 software update os 7.1 download. Cooling circuit is overheated.
Check unhindered air circulation through
the vents and allow device to cool down.
the vents and allow device to cool down.
Err 20
(only 5424 R)
(only 5424 R)
Temperature sensor in rotor chamber faulty.
Switch the centrifuge off and back on
again after > 20 s.
again after > 20 s.
Eppendorf 5424 Service Manual Pdf
![Service manual tv Service manual tv](/uploads/1/2/5/0/125028597/202172210.jpg)
Err 21
(only 5424 R)
(only 5424 R)
Temperature sensor at capacitor faulty.
Switch the centrifuge off and back on
again after > 20 s.
again after > 20 s.
Err 24
(only 5424 R)
(only 5424 R)
Cooling unit fault, e.g., overheating.
Allow the centrifuge to cool down and
repeat the cycle.
repeat the cycle.
EN
O
perating manual
Advertising
This manual is related to the following products:
Popular Brands
Eppendorf Centrifuge 5424
Popular manuals